BEGINNER'S PLUMBING: WHAT YOU NEED FOR BATHTUB INSTALLATION

Beginner's Plumbing: What You Need for Bathtub Installation

Beginner's Plumbing: What You Need for Bathtub Installation

Blog Article

Schedule An Appointment

The writer is making a number of good observations relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround overall in this great article just below.


How to Install a Bathtub Yourself
Mounting a bath tub isn't specifically rocket science, however it does need solid plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is additionally a moderately hard project. If the old tub is readily accessible, the job can relocate rapidly; if you have to open a wall surface to eliminate the old tub and also position the new bath tub, the job is much harder. In either case, the task is within a house handyman's abilities, although you will certainly need an assistant to move out the old tub and set in the new one. Make sure you have qualified yourself for the job and are comfortable attempting it. As opposed to employing a specialist to take over a halfway-completed job, it is much better to take into consideration using one prior to you begin. Chances are you might require a professional plumber to make tube connections.
This article will certainly help you set up a new tub in your washroom if you have already acquired a brand-new bathtub and also do not need to alter the setup of your previous water supply pipelines.
Your tools as well as product list need to consist of the following:
  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipeline Caps


  • Removing Old Taps


    If you require to replace old taps with new ones as a part of your setup, after that the first thing you ought to do is separate the supply of water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The process of getting rid of the existing taps can be fairly bothersome as a result of the restricted access that is often the case.
    Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the taps. Have a fabric all set for the continuing to be water that will come from the pipes. When the supply pipes have actually been eliminated, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from turning during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly need to be cleansed of any old securing compound.
    Prior to carrying on to fit the new taps, compare the pipeline connections on the old taps to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.

    Fitting New Taps


    If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the tap and also the other end offers a link to the existent supply pipelines.
    If you require to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
    Next, position the tap in the mounting opening in the bath/basin making sure that the washers are in area between the tap and the sink. Safeguard the faucet in place with the maker provided backnut. When the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular tap adapters. The previous type ought to be connected to the tap ends initially, tightening just by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.

    Mounting the Tub


    Using both wooden boards under its feet, put the bathtub in the required setting. The wood boards are handy in evenly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four small points.
    The following goal is to make sure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the bathtub until the level reads degree.
    To set up taps, fit all-time low of the furthest flexible faucet port to the appropriate supply pipe by making a compression sign up with; then do the very same for the various other tap.
    Turn on the water supply as well as check all joints as well as brand-new pipework for leakages as well as tighten them if essential. Fill the tub and likewise check the overflow electrical outlet and the typical electrical outlet for leakages.
    Finally, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the tub should wait up until the tub has been made use of a minimum of once as this will settle it right into its last setting.

    Getting ready for the Installation


    Firstly, the sustaining structure supplied with the bathroom must be fitted (if needed) according to the producer's directions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets system to prevent stress on the tub.
    Fit the adaptable tap ports to the bottom of the two faucets utilizing 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you use all of the supplied washers.
    Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom should currently prepare to be fitted in its last placement.

    Tiling Around the Bathtub


    In the area where the bathroom satisfies the tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture a rigid seal, triggering the water to pass through the wall in between the bath and the tiling, causing problems with wetness and also possible leaks to the ceiling below.
    You can select from a range of coloured sealers to blend in your components and also installations. They are marketed in tubes and also cartridges, as well as can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always load the bath tub with water before securing, to allow for the motion experienced when the tub is in use. The sealant can fracture fairly early if you do not take into account this movement prior to sealing.
    Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly readily available on the market. It is advisable to fit the ceramic tiles utilizing water-resistant or water-proof glue and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    I was shown that write-up on Installing A Bathtub from an associate on another site. Liked our write-up? Please share it. Help someone else find it. We appreciate reading our article about How to Install a Bathtub Yourself.


    Professional service available.

    Report this page